GE Oven F-Codes: F2, F3, F9 and More

Quick answer: GE oven F-codes point to a part: F3 and F4 usually mean the oven sensor, F2 means the oven ran too hot, F9 is the door lock, and F0, F1, F6 and F7 point to the keypad. A breaker reset can clear a code, but if it returns the oven needs service.

GE ranges and wall ovens with electronic controls show F-codes in the clock display, often with a steady beep. GE notes that codes vary by model, and not every code exists on every oven. Start with a reset: turn off the circuit breaker or fuse for a minute or two, then restore power. If the code comes back, GE advises leaving the oven off at the breaker until it is serviced; you can switch it on briefly to use the cooktop. If you ever smell gas, do not touch any switches or the oven controls. Leave the home right away and call your gas utility from outside.

GE Oven Error Codes (F-Codes) list

F0 / F1 / F6 / F7

Keypanel (touchpad) problem.

Common causes: Worn or shorted keypad, moisture behind the panel.

What you can try: Breaker reset for a minute or two.

Call a technician if: The code returns. The keypanel often needs replacing.

F2 / F20

Oven temperature went above a preset limit.

Common causes: Sensor, control relay or wiring fault.

What you can try: Turn the oven off at the breaker and let it cool.

Call a technician if: Always. Do not keep using an oven that is overheating.

F3 / F4

Oven temperature sensor fault.

Common causes: Failed sensor or sensor wiring.

What you can try: Breaker reset.

Call a technician if: The code returns. The sensor usually needs replacing.

F5 / F8 / FF

Electronic control fault.

Common causes: Failed control board.

What you can try: Breaker reset.

Call a technician if: The code returns.

F9 / FC

A part in the door lock circuit has failed.

Common causes: Lock motor, switch or wiring.

What you can try: Breaker reset. Make sure nothing is blocking the door.

Call a technician if: The code returns or the door stays locked.

F350

Upper cooling fan circuit problem or a blocked fan.

Common causes: Obstruction or fan fault.

What you can try: Check whether anything is blocking the cooling vents.

Call a technician if: Nothing is blocking it and the code remains.

Probe or probe receptacle fault.

Common causes: Damaged meat probe or socket.

What you can try: Remove the probe and see if the code clears.

Call a technician if: It shows with no probe inserted.

Bad Line

Power is connected but the unit is wired incorrectly.

Common causes: Installation wiring error.

What you can try: Do not use it.

Call a technician if: An installer or electrician must correct the wiring.

LOC / Loc Door

LOC is the child lockout. A flashing LOC DOOR when you did not start self-clean is a control issue.

Common causes: Lockout turned on, or the control needs a reset.

What you can try: Check the owner's manual to turn off the lockout. For a flashing LOC DOOR, do a breaker reset.

Call a technician if: The door will not unlock after a reset.

OFF

Self-clean cannot start because the oven is too hot, or Bake was tried too soon after a clean.

Common causes: Oven still cooling.

What you can try: Let the oven cool fully and try again.

Call a technician if: Not usually needed.

How to clear the code

Turn off the oven's breaker (or remove the fuse) for a minute or two.
Restore power and set the clock.
If the F-code returns, turn the breaker off again and keep it off until the oven is serviced. You may switch it on briefly to use the cooktop.

Gas range safety

An F-code on a GE gas range is an electronic fault, but some faults stop the oven from lighting. Never try to light the oven by hand or open the gas valve area. If you smell gas, leave the home and call your gas utility from outside. Gas valve and burner work is not a DIY job.

GE range and wall oven repair in Atlanta

Sensor, keypad, control and door lock repairs are routine for our technicians. Mr. Fixer repairs GE, GE Profile and Café ranges and wall ovens across Metro Atlanta. Call (678) 866-3669 or book online. If your oven is heating poorly without a code, read oven not heating: causes and fixes.

Code still showing?

Our technicians repair GE oven & cooktops across Metro Atlanta, usually the same day. Diagnostic from $80, credited toward your repair.

Call (678) 866-3669

FAQs

What does F3 mean on a GE oven?

On many GE ovens F3, like F4, points to the oven temperature sensor. A reset may clear it briefly, but if it returns the sensor usually needs replacing.

Is it safe to use my GE oven with an F2 code?

No. F2 means the oven went above a safe temperature limit. Turn it off at the breaker and have it checked.

My GE oven door is stuck locked after self-clean. What do I do?

Let the oven cool completely, then try a breaker reset. If the door still will not unlock or F9 shows, the door lock circuit needs service.

Codes and meanings vary by model and model year. Check your owner's manual for your exact model.

GE Oven Error Codes (F-Codes): What They Mean and How to Fix Them